首页 » 博客 » 再生涡轮泵维护

再生涡轮泵维护

铁路行业和宝德解决方案

Last updated Feb 5, 2025 | Published on Sep 6, 2018

如何维护您的再生涡轮泵,延长系统寿命

While well-selected regenerative turbine pumps offer exceptionally long service life in chiller applications, like all pumps, there are many circumstances that can significantly impact service life. The following items should be carefully considered when installing and using regenerative turbine pumps to ensure a long, trouble-free operating life. Regenerative turbine pumps are capable of very high pressures, so they have very tight running clearances (typically .002″ ~ .006″) to help prevent internal loss of this pressure. As a result, please be aware that regenerative turbine pumps are very intolerant of grit and abrasive material in the fluid stream. Fluid contamination tends to erode impeller vanes, lodge between the impeller and casing, and cause premature failure in mechanical seals.

系统启动

System startup is especially critical because even if fluid is clean and grit free, new piping systems often have solder spatter, pipe dope, and metal chips in them. Older systems may occasionally release clumps of pipe scale and rust into the pump, both causing minor damage that can accumulate over time to reduce performance. In either case, it is important to flush and inspect the system before startup. Installation of a suction strainer is very useful in protecting the pump if the strainer is cleaned regularly. This issue alone is probably the most common mode of failure for regenerative turbine pumps, so proper consideration should be given to protecting the pump from this type of damage. Protect the pump from “dead-head” conditions where discharge is completely shut off while in operation. While some turbines are tolerant of short periods of zero flow, mechanical seal damage, pump and/or motor overheating, and even system damage due to excessive overpressure may occur as a result of running a pump in this state. Always make sure all system valves are open and piping is restriction-free before pump startup. If you anticipate this condition, use a properly sized relief valve and/or overpressure cutout system to protect the pump and system.

阀门、压力冲击及干运转

The use of modulating valves or other conditions that would cause sudden pressure shocks on the system are detrimental to regenerative turbine life. The self-adjusting balanced impeller feature relies on the pump attaining pressure equilibrium within a reasonable period of time. Sudden pressure shocks alter that balance and may cause the impeller to rub against the casing until equilibrium is regained. Continuous repeated pressure shocks from modulating valves or other system components can keep the impeller in a constant state of flux and cause excessive impeller rubbing and eventual failure. All pumps should be protected from dry running. Please assure that all system valves are open, and pump suction is flooded before startup. Momentary jogging of pumps to confirm proper rotation is permissible.

净正吸入压头

为泵提供适当的NPSH(净正吸入压头)可用性。尽管一些再生涡轮泵可承受不良NPSH条件(不良NPSH导致气穴现象以及液体急剧蒸发进入气态),但持续长时间运行设备会缩短使用寿命。液体中存在蒸气就不能提供机械密封件、无封泵轴承及叶轮流体动力薄膜所需的润滑和冷却。这种条件与干运转无异,只是程度更轻微。此外还应注意吸入液体中的任何流量限制条件,包括所选不良吸滤器、吸入管径不足以及吸入阀未完全打开,也会造成气穴现象、急剧蒸发以及不完全干运转条件,导致性能降低和过早出现故障。

执行预防性维护时间表

Key to avoiding many of the issues above is a good preventive maintenance program. All pumps will eventually fail if maintenance is ignored completely. Mechanical seals, sealless pump bearings, and impellers should be examined for unusual or excessive wear, fluid chemistry should be monitored and maintained, suction strainers should be cleaned regularly, relief valves should be tested, and many other items relating to the system itself should be checked on a regular basis to help prevent problems that could affect pump service life. For common applications, we recommend that you keep a basic spare parts kit on hand at all times. For more critical services, a duplicate pump is often the most expedient and cost effective way to prevent or minimize downtime. Regenerative turbine pumps have been used successfully for over 35 years in many different applications such as chillers, heat exchangers, boiler feed, spraying, reverse osmosis, fire protection, refrigeration, chemical process and recirculation. Long service life in a pump relates as much to the pump and system design as it does to the quality and execution of the preventive maintenance plan. As with any piece of equipment there is no substitute for using the right tool for the job.

相关文章

医疗诊断类型

医疗诊断类型

在革命性的医疗保健世界中,医学诊断分析可帮助临床医生评估健康状况、检测...

您可能还喜欢

有疑问?我们随时可以提供帮助!